Key Learning Device for Nissan key V2 and Infinity
 
Supported models:
- Nissan Altima Intelligent Key 2013+
- Nissan Juke Intelligent Key 2013+
- Nissan Pathfinder Intelligent Key 2013+
- Nissan Pulsar Intelligent Key 2014+
- Nissan Rogue Intelligent Key 2014+
- Nissan Qashqai Intelligent Key 2014+
- Nissan X-Trail Intelligent Key 2014+
- Nissan Maxima Intelligent Key 2016+
- Nissan Murano Intelligent Key 2015+
- Infiniti JX35 Intelligent Key 2013+
- Infiniti Q50 Intelligent Key 2014+
- Infiniti QX50 Intelligent Key 2014+
- Infiniti QX60 Intelligent Key 2014+
- Nissan Juke F16 2019+ (connection to internal CAN-BUS is required)
- Nissan X-Trail T33 2021+ (connection to internal CAN-BUS is required)
- Nissan Sentra B18 2019+ (connection to internal CAN-BUS is required)
- Nissan Qashqai/ Rogue J12 2021+ (connection to internal CAN-BUS is required)
Keys count selection (1 to 4 keys can be learned):
- All SW to OFF – 1 key will be learned
- SW1 ON – 1 key
- SW2 ON – 2 keys
- SW3 ON – 3 keys
- SW4 ON – 4 keys
- SW5 ON – 4 keys
- SW6 ON – 4 keys
- SW7 ON – 4 keys
- SW8 ON – 4 keys
NOTE: Highest selected SW is taken into account e.g. if SW1 and SW3 are ON – 3 keys
should be learned
Nissan device LED states:
1. At startup the LED blinks GREEN slowly 3 times - this means that the hardware test
passed OK
2. Alternate LED green/red - the device is working
3. Fast blink GREEN -> press START (and hold if necessary) to turn IGNITION ON
4. Fast blink RED -> press START with new key logo to turn IGNITION ON
5. Continiously RED -> touch START with new key logo and wait IGNITION to switch ON
6. LED OFF -> press START to turn IGNITION OFF
7. Alternate LED green/red - the device is working
8. Slowly blink GREEN - finished OK
9. Fast blink RED - finished with ERROR
NOTE (specific for UDS models - Qashqai, X-Trail e.t.c): When invited to press or touch
the START with a new key but all required keys are already learned use any of the learned keys!
Sometimes after the key learning procedure is done it might be required to turn a few
times IGN ON and then OFF until the "Key not detected" message disappears.
At the end verify that the new keys are working by pressing the brakes and starting the engine
one by one.
For the models related to the:
- Nissan Juke F16 2019+
- Nissan X-Trail T33 2021+
- Nissan Sentra B18 2019+
- Nissan Qashqai/ Rogue J12 2021+
There are specifics regarding the connection between the D051 device and the vehicle. These
vehicles require you to connect directly to the internal CAN-BUS of the vehicle.
There are three options for internal CAN-BUS connection:
USM (Under hood Switching Module), connector CT1: pin4 - CAN-L, pin6 - CAN-H
BCM (Body Control Module), connector DS1: pin27 - CAN-L, pin26 - CAN-H
HFM (Hands Free Module), connector S1: pin7 - CAN-L, pin6 - CAN-H
In Nissan vehicles there is a pattern that the color for the internal CAN is as follows: CAN-L = pink
wire, CAN-H = blue wire.
In these models you need to take an extra step before you start using D051.
To connect to the internal CANBUS of the vehicles, the D051 is equipped with an additional cable set consisting of male and female OBDII extender connectors, as well as an additional pair of needle connectors for CAN H and CAN L.
 
Before you start the procedure:
1. Connect the male OBD connector to the OBD port of the vehicle
2. Connect the CAN H and CAN L needle connectors to the CAN H and CAN L of the vehicle as per the above description
Here is an example of the connection between the needle connectors and the CAN H and CAN L wires of the USM:
After you have connected the male/ female OBD extender cable and the CAN H/L cable to the
internal CANBUS your D051 is ready to operate.